How to store and dispose of LiPo batteries: voltage, place, recycling
A full LiPo left lying around for weeks ages quickly and can swell. A damaged one belongs neither in a drawer nor in the household bin. Here is the voltage you store LiPo, LiHV and Li-ion at, how long a pack may stay full, where and how warm it should be kept, what to do with a swollen or crashed pack and, for Germany and the EU, where you can hand it in for free. The figures come from documents of battery and charger makers, the handling advice from the German Environment Agency (UBA) and the Federal Institute for Materials Research and Testing (BAM), the legal part from the German Battery Act (BattDG) and the EU Battery Regulation. Everything was read on Nov 13, 2026.
The short version
- Storage voltage per cell: LiPo around 3.8 V, LiHV 3.8 to 3.85 V, Li-ion 3.7 V (charger presets). The charger’s storage mode takes the pack there.
- Don’t leave packs full: BetaFPV says 3 days at most. According to CNHL a full pack can start to suffer within a day or two.
- Storage: unplugged, in a non-conductive, fireproof container, not loose together, not in the car and not in the sun, out of reach of children.
- Swollen or damaged in a crash: don’t charge, discharge or fly it again. Watch it in a safe place, put it in a fireproof container, then take it to a collection point. No salt water.
- Disposal: never in the household bin. In Germany, shops that sell portable batteries and the municipal recycling center take waste packs back for free, swollen ones included, and you don’t have to buy anything. Tape the terminals first.
Storage voltage per battery type and source
The storage voltage is the voltage per cell a pack should sit at while you don’t use it. E-flite: “A Li-Po cell is approximately 50% charged when it is at 3.8V.” Grepow: “for a battery that’s removable, you should discharge the battery down to about the halfway mark”. The table shows what each source gives per battery type, all values per cell. The label tells you which type your pack is; how to tell LiPo, LiHV and Li-ion apart is in How to charge LiPo batteries.
| Source | LiPo | LiHV | Li-ion |
|---|---|---|---|
| Gens Ace/Tattu (battery)manual (PDF) | 3.6–3.9 V¹ | – | – |
| Grepow (battery)storage blog, LiHV blog | 3.8–3.85 V | 3.8 V | – |
| CNHL (battery)storage blog, LiHV blog | around 3.8 V | 3.80–3.85 V | – |
| BetaFPV (battery, LAVA II 1S)product page | – | 3.85 V² | – |
| E-flite (battery, 2009)guide 2009 (PDF) | 3.8 V³ | – | – |
| ISDT (charger, preset)Q6 Nano (PDF), 608AC (PDF) | 3.80 V | 3.85 V | 3.70 V |
| SkyRC (charger)B6ACneo (PDF) | 3.8 V | 3.85 V | 3.7 V |
| ToolkitRC (charger)Q6AC (PDF) | storage mode for all three, no figure in the manual | ||
– no figure for this type
¹ for storage over 3 months
² spec table; for long-term storage the warnings give 3.8 to 3.9 V
³ about half charged, according to E-flite
What the differences mean
- LiPo: the figures range from 3.6 to 3.9 V (Gens Ace/Tattu, for storage over 3 months) to 3.8 to 3.85 V (Grepow). 3.8 V lies within every one of them, and it is what ISDT and SkyRC preset for storage. CNHL: “When you buy a brand-new LiPo battery, it usually comes with a storage charge”, often between 3.75 and 3.85 V.
- LiHV: 3.8 V (Grepow) to 3.85 V (BetaFPV spec table, ISDT, SkyRC). BetaFPV gives 3.8 to 3.9 V for long-term storage, CNHL 3.80 to 3.85 V as a practical target.
- Li-ion: only the chargers give a figure, 3.7 V. We found no figure from a battery or cell maker on its own site; go by your pack’s datasheet.
CNHL: “Many chargers target approximately 3.8–3.85V per cell for a standard LiPo, although the exact program target can vary. Follow the battery and charger instructions where they specify a particular value.”
Voltage of the whole pack
If you measure the whole pack rather than single cells, multiply the storage voltage by the cell count. CNHL gives this as a rule of thumb for LiHV (“total storage voltage ≈ 3.8V × cell count”), and E-flite lists the same values as this table for LiPo (2S 7.6 V, 3S 11.4 V, 4S 15.2 V, 6S 22.8 V). The table uses the ISDT charger presets.
| Cells | LiPo (3.80 V) | LiHV (3.85 V) | Li-ion (3.70 V) |
|---|---|---|---|
| 1S | 3.80 V | 3.85 V | 3.70 V |
| 2S | 7.60 V | 7.70 V | 7.40 V |
| 3S | 11.40 V | 11.55 V | 11.10 V |
| 4S | 15.20 V | 15.40 V | 14.80 V |
| 6S | 22.80 V | 23.10 V | 22.20 V |
Storage mode: when and how
How long may a pack stay full? Not long. BetaFPV: “Do not store fully charged batteries for more than 3 days.” CNHL on packs left full: “This degradation happens quite quickly–sometimes even within a day or two–and leads to swelling, puffiness, and overall loss of battery capacity.” Grepow: “If you leave your battery at maximum voltage, you run the risk of decreasing the battery’s lifespan and causing your battery to swell.” But CNHL also says: “A LiPo battery should not remain fully charged or deeply discharged for extended periods.” So if you won’t fly in the next few days, take the pack to storage voltage.
That is what the charger’s storage mode is for. SkyRC: “This mode is to store the battery via charging or discharging its votlage to a specific storage value.” ISDT and SkyRC set the target per battery type themselves (table above); ToolkitRC has the mode but gives no figure in the manual.
- Let it cool. After flying or charging, let the pack cool first, then store it. CNHL: “Heat plus high voltage is what accelerates aging.”
- Connect the balance lead. CNHL: “It's essential that you use balance mode to ensure proper storage charging.” How to connect it is in How to charge LiPo batteries: balance charging.
- Battery type and cell count as on the label, then select “Storage”.
- Not “Discharge”. CNHL: “If you mistakenly use "Discharge" mode, the charger will continue discharging the battery until it's completely drained, which can damage the battery.”
- Stay with it. Don’t leave storage charging unattended either. CNHL: “If you absolutely need to leave the room, unplug the battery and shut everything off.” The charger stops by itself at storage voltage.
A large, full pack takes time, because chargers discharge with far less power than they charge; CNHL: “A large, fully charged 6S battery can therefore take hours to reach storage voltage.” And storage mode doesn’t replace looking at the pack. CNHL: “Do not use Storage mode as a substitute for inspecting the battery. A swollen, damaged or abnormal pack still requires appropriate isolation and assessment.” See swollen and damaged packs.
Where and how to store packs
- Unplugged and in a container. Gens Ace/Tattu: “Always disconnect Batteries when not in use and store Batteries in a non-conductive and fireproof container.” E-flite: “it is best to store and transport the battery in a non-conductive (and preferably fire-proof) container and/or to cover the connectors with a non-conductive material.” CNHL: “Store in a cool, dry, fire-safe place”. For a quad that means: unplug the pack and take it out.
- No short circuits. Gens Ace/Tattu: “Never store loose Batteries together, the Batteries’ terminals may contact one another causing a short circuit.” The German Environment Agency (UBA) warns that a short circuit, for example metal on metal at the terminals, can lead to fire or explosion.
- Not in the sun, not in the car. Gens Ace/Tattu: “Never storage Batteries to extreme temperatures or direct sunlight.” E-flite: “Do not store the battery in a car or direct sunlight whenever possible. If stored in a hot car, the battery can be damaged or even catch fire if the temperature inside the car becomes too hot.” The UBA advises against outdoors, damp rooms and hot places such as a garden shed or the shelf behind the windscreen.
- Away from ignition sources where possible (BAM).
- Out of reach of children. E-flite: “Keep batteries out of reach of children, unless supervised by a responsible adult.”
- Protect them from knocks. Gens Ace/Tattu: “Never alter, puncture or impact Batteries or related components.” The UBA: protect them from knocks, blows and drops.
Temperature
There is no single figure, but the sources are close: around room temperature, not in the heat, not in frost. The fridge is no answer either; the UBA advises against it because of condensation.
| Source | What it says |
|---|---|
| Gens Ace/Tattumanual (PDF) | −10 to 45 °C; over 3 months 23 ± 5 °C at 65 ± 20 % humidity |
| Grepowstorage blog | ideal 70 °F (21 °C), not too cold and not too hot |
| E-flite (2009)guide 2009 (PDF) | room temperature; short-term storage or transport at about 40 to 120 °F (about 4 to 49 °C) |
| CNHLLiHV blog | cool, dry, fire-safe; no figure |
| German Environment Agency (all lithium batteries)UBA | best 10 to 25 °C; above +50 °C and below −20 °C the service life suffers badly; not in the fridge (condensation) |
Transport: car, plane, shipping
- Car and backpack. E-flite recommends the same non-conductive, preferably fireproof container or covered connectors for transport, and not leaving packs in a hot car.
- Plane (German Federal Aviation Office, ICAO rules). According to the LBA, loose spare lithium batteries may only go in cabin baggage, never in checked baggage. Each may have at most 100 Wh; with the airline’s approval up to 160 Wh, and then no more than two such spares per person. Every spare must be protected against short circuits individually: in its original retail packaging, with taped terminals or in its own plastic bag or protective pouch (ICAO table at the LBA). Airlines can be stricter; the LBA says to contact them in any case.
- Working out watt-hours. Nominal voltage times capacity in amp-hours. A 6S with 1300 mAh has 22.2 V × 1.3 Ah ≈ 29 Wh, a 6S with 2200 mAh about 49 Wh (our own calculation, with 3.7 V nominal per LiPo cell).
- Shipping. Lithium batteries are dangerous goods; legal rules and labelling duties apply when you send them (BAM). Don’t ship a damaged pack (Gens Ace/Tattu).
Swollen, damaged, crashed
How to spot a failed pack. According to the UBA, a lithium battery has failed if it is swollen, deformed, has vented or leaked, or shows a greasy film or deposits at the terminals. Gens Ace/Tattu: “Stop using it if user found the cells are not balanced or cells are puffing or weeping.” They also list damage to the cell’s plastic envelope and a smell of electrolyte. The BAM: a battery that is too hot to touch while it isn’t charging, or that releases gas, is dangerous.
Don’t keep using it. Every source agrees:
- The UBA: failed batteries should on no account be used again or even opened; if their safety mechanisms fail, they can ignite or explode spontaneously.
- E-flite: “A battery that has ballooned or swollen even a small amount must be removed from service completely.” And: “Continuing to charge or discharge a battery that has begun to balloon or swell can result in a fire.”
- BetaFPV: “Do not use batteries that are deformed or swollen.”
- Don’t open it: according to the BAM the electrolytes and conducting salts are toxic; Gens Ace/Tattu: “Never disassemble the cells.”
What to do
- Disconnect. Gens Ace/Tattu: “Quickly and safely disconnect the battery from the charger or model.”
- Move it to a safe place. Gens Ace/Tattu: “Then place the battery and/or charger in a safe, open area, away from flammable materials inside a fireproof container (such as a LiPo safety bag). After one hour, if the battery condition has stabilized, remove the battery from service. Do not continue to handle, attempt to use, or ship the battery.” And: “A safe area should be outside of any building or vehicle and away from any combustible materials. A battery can still ignite even after one hour.”
- After a crash, E-flite: “you must quickly (and safely) disconnect and remove the battery from the model, then place it in a safe, open area away from flammable materials to observe it for at least 15 minutes. DO NOT place the crash damaged battery in a car or other location that is not fireproof.” Even a pack that stays calm for those 15 minutes may still catch fire when handled, “up to many hours after the damage occurred”; E-flite: “it is best to place the damaged battery inside of a fireproof container until it can be disposed of properly.”
- Take it to a collection point soon. The UBA recommends: tape the terminals, use a closable container (box, tin, bucket or jar, which can also be filled with sand), and when you hand it in, speak to the staff and point out the damage. In Germany, retailers must take back swollen packs too; see below.
Leaking? Don’t touch it without gloves and wash your hands thoroughly afterwards (UBA). Electrolyte on your skin, E-flite: “wash the affected area(s) with soap and water immediately. If the electrolyte comes into contact with your eye(s), flush them with generous amounts of water for 15 minutes and seek immediate medical attention.”
Smoking or burning? According to the UBA, burning lithium batteries release highly irritating, corrosive and toxic fumes. For small lithium batteries that are deformed, venting or smoking, the BAM advises placing them in a container with a lot of water to cool them down, with care, because the escaping gases are toxic. For large ones, the BAM says to call the fire brigade if necessary.
Salt water? No
The internet often says to discharge old LiPos in salt water. In the documents of the makers we read (Gens Ace/Tattu, Grepow, CNHL, BetaFPV, E-flite, ISDT, SkyRC, ToolkitRC) and at the UBA and the BAM, this is nowhere recommended. Gens Ace/Tattu say the opposite: the cells “shall never be soaked with liquids such as water, seawater”. The UBA warns that lithium can be damaged when it comes into contact with water. The BAM’s water is emergency cooling, not discharging and not a way of disposal. Afterwards the pack still goes to a collection point; the BAM names the take-back points in shops and the municipal recycling center.
Disposal in Germany and the EU: what the law says
This section covers Germany and the EU only. Since Aug 18, 2025, the waste battery rules of the EU Battery Regulation (EU) 2023/1542 apply directly in every EU country (Art. 96). In Germany, the Battery Act (BattDG) has added to them since Oct 7, 2025; it replaces the old Batteriegesetz (BattG), which according to the UBA has thereby largely ceased to apply. Older guides and some official pages still name the old act. Quotes from German law are our translations. This is not legal advice, it is a summary of the linked laws.
Is an FPV pack a portable battery?
The regulation distinguishes battery categories. A portable battery is “a battery that is sealed, weighs 5 kg or less, is not designed specifically for industrial use and is neither an electric vehicle battery, an LMT battery, nor an SLI battery” (Art. 3(1)(9)). Regulation (EU) 2023/1542 An FPV pack is sealed, weighs well under 5 kg and isn’t built for industrial use, so under this definition it is a portable battery. That is our own classification; we found no authority that names FPV packs explicitly.
Your duty: hand it in separately
The EU regulation says: “End-users shall discard waste batteries separately from other waste streams, including from mixed municipal waste.” (Art. 64(1)). The German BattDG adds that end users must take waste batteries to a collection separate from unsorted municipal waste, and that waste portable batteries may only be collected via take-back and collection points connected to a producer responsibility organization. Sec. 6(1) and (2) BattDG So the household bin, the recycling bin for packaging, bulky waste and scrap metal are out; the UBA lists them explicitly. The crossed-out wheelie bin symbol on the pack or its packaging points to this too. The law says nothing about discharging or taping; that advice comes from the UBA (below).
Where to hand it in (Germany)
- In a shop. Under EU law, retailers take back waste batteries “free of charge and without imposing an obligation on the end-user to buy or to have bought a new battery” (Art. 62(1)); the duty “shall be limited to the categories of waste batteries which the distributor has or had as batteries in its offer and, for waste portable batteries, to the quantity that non-professional end-users normally discard” (Art. 62(2)(b)). In Germany, every retailer must take back waste portable batteries in the shop or in its immediate vicinity free of charge, regardless of chemistry, brand, origin, size and condition. Sec. 14(1) BattDG According to the UBA you find collection boxes wherever new portable batteries are sold: supermarket, discounter, department store, drugstore, electronics store, DIY store. Shops must put up a sign saying that waste batteries can be returned there free of charge (Sec. 24(1) BattDG).
- Bought online. In Germany, retailers who sell batteries by mail order must set up suitable return options within a reasonable distance of the customer (Sec. 14(2) BattDG) and give that information on their website or with the delivery (Sec. 24(3) BattDG).
- Municipal recycling center. In Germany, the public waste management authorities must accept waste portable batteries from private households free of charge, regardless of chemistry, brand, origin, size and condition. Sec. 15(1) BattDG The UBA names the municipal recycling center (Wertstoffhof) and the mobile hazardous waste collection (Schadstoffmobil) as municipal collection points.
Swollen packs too
The BattDG requires take-back regardless of the battery’s condition, in shops and at the recycling center alike. The UBA says it directly: retailers must also take back batteries that are damaged, for example leaking, swollen or burst. Don’t just drop a damaged pack into the collection box: according to the UBA, speak to the staff, point out the damage and bring it in a suitable container.
How to prepare it
- Tape the terminals. The UBA advises taping the terminals of waste lithium batteries beforehand to prevent external short circuits. E-flite suggests covering the connectors with a non-conductive material.
- Pack it. Damaged packs go in a closable container (UBA). Don’t put several packs together loose; their terminals may touch (Gens Ace/Tattu).
- Discharge first? Neither the BattDG nor the UBA requires it. Some chargers have a function for it: ISDT calls it “Destroy”, a task for a battery to be scrapped that is “capable to discharge the battery to 0V”. But don’t charge or discharge a swollen or damaged pack any more (Gens Ace/Tattu, E-flite).
Read on
How to charge correctly, with end-of-charge voltage, balance lead and charge current, is in How to charge LiPo batteries. Which batteries and which charger suit the beginner whoops: Buying your first FPV drone. And what applies when you fly with goggles in Germany: Flying FPV legally in Germany.
Sources
As of Nov 13, 2026; every source was read that day. Nothing here was tested on a device. Maker names appear as sources, not as recommendations. The UBA pages on lithium batteries (2023) and on disposal (2024) still name the old German battery act; the legal part above follows the BattDG and the EU regulation. German sources are in German.
- Laws: Regulation (EU) 2023/1542 (batteries and waste batteries), consolidated 31.07.2025, Regulation (EU) 2023/1542, German version, German Battery Act (BattDG), in force since 7 Oct 2025 (German), Section 6 BattDG, duties of the end user (German), Section 14 BattDG, take-back duties of retailers (German), Section 15 BattDG, public waste authorities (German), Section 24 BattDG, information duties of retailers (German).
- Authorities: German Environment Agency (UBA), handling lithium batteries (German), German Environment Agency (UBA), using and disposing of batteries (German), German Environment Agency (UBA), batteries and waste batteries: legal basis (German), BAM (Federal Institute for Materials Research and Testing), handling lithium batteries safely (German), German Federal Aviation Office (LBA), electronic devices with lithium batteries (German), LBA, Table 8-1 of the ICAO Technical Instructions 2025-2026 (German, PDF).
- Battery makers: Gens Ace/Tattu, LiPo operating instructions (PDF), Grepow, storing LiPo batteries, Grepow, What is a LiHv battery?, BetaFPV, LAVA II 1S (spec table and warnings), CNHL, storage charging LiPo batteries, CNHL, how to charge and store LiHV batteries, CNHL, LiPo charger modes explained, E-flite (Horizon Hobby), LiPo battery guide from 2009 (PDF).
- Chargers: ISDT, Q6 Nano manual (PDF), ISDT, 608AC manual (PDF), SkyRC, B6ACneo manual V1.3 (PDF), ToolkitRC, Q6AC manual V1.2 (PDF).
Last updated: Nov 14, 2026