Converting Betaflight rates to Actual

Still flying Betaflight rates with RC Rate, super rate and RC Expo and want to switch to Actual Rates without the quad feeling different? The Betaflight App does not convert when you switch. Here is how the conversion works and where the two curves never quite match. The converter also turns any of the five rates types into any other: Betaflight, Raceflight, KISS, Actual and Quick.

What the Betaflight App does when you switch

When you change the Rates Type under PID Tuning → Rate Profile Settings, the app asks first and warns: “If you change the rates type your rates will be set to a default curve.” Which curve that is can be found in the app's source code (RatesSubTab.vue, function setDefaultsForRatesType, as of 4 November 2026): for Actual it sets Center Sensitivity 70, Max Rate 670 and Expo 0 on all three axes, for Betaflight rates RC Rate 1.00, Rate 0.70 and RC Expo 0. After you confirm, the defaults are in the fields and your old values are gone, so write them down first.

The formula for Betaflight rates

This is how Betaflight turns the stick position into a turn rate with Betaflight rates (file src/main/fc/rc.c, function applyBetaflightRates, Betaflight 2026.6.2, unchanged in the current development version):

if (currentControlRateProfile->rcExpo[axis]) { const float expof = currentControlRateProfile->rcExpo[axis] / 100.0f; rcCommandf = rcCommandf * power3(rcCommandfAbs) * expof + rcCommandf * (1 - expof); } float rcRate = currentControlRateProfile->rcRates[axis] / 100.0f; if (rcRate > 2.0f) { rcRate += RC_RATE_INCREMENTAL * (rcRate - 2.0f); } float angleRate = 200.0f * rcRate * rcCommandf; if (currentControlRateProfile->rates[axis]) { const float rcSuperfactor = 1.0f / (constrainf(1.0f - (rcCommandfAbs * (currentControlRateProfile->rates[axis] / 100.0f)), 0.01f, 1.00f)); angleRate *= rcSuperfactor; }

Here rcCommandf is the stick position from −1 to 1. In words:

  • RC Expo (roll_expo ÷ 100) bends the stick travel first: one part grows with the fourth power, the rest stays linear.
  • RC Rate (roll_rc_rate ÷ 100) times 200 is the base slope. Above 2.0 every hundredth counts 15.54 times (constant RC_RATE_INCREMENTAL = 14.54).
  • Super rate (“Rate” in the app, roll_srate ÷ 100 in the CLI) divides by 1 − stick × super rate. Near center that changes very little, towards full stick more and more.
  • Finally roll_rate_limit caps the turn rate, at 1998 °/s by default.

Pitch and yaw work the same with pitch_… and yaw_…. The formula for Actual Rates and what center, max and expo do there is in the guide Actual Rates explained.

Center and full stick, worked out

Two values follow from the formula that you can carry over to Actual exactly. The calculation is by fpvrates, it is not stated like this in the docs:

  • Center: the slope at stick 0 is 200 × RC Rate × (1 − RC Expo). In Actual that is the Center Sensitivity. Without RC Expo it is exactly the “times 200” rule of thumb from the 4.2 tuning notes. With RC Expo the center gets flatter: RC Rate 1.00 with RC Expo 0.30 corresponds to 140, not 200.
  • Full stick: at full stick you get 200 × RC Rate ÷ (1 − super rate). In Actual that is the Max Rate. For the app's default curve (RC Rate 1.00, Rate 0.70) that is 200 ÷ 0.3 = 666.7 °/s, almost exactly the 670 that Actual has by default.

Actual stores both values in steps of 10 °/s (in the CLI roll_rc_rate is the center ÷ 10 and roll_srate the max ÷ 10), and the converter rounds accordingly. The 4.2 tuning notes also say that the two numbers are directly comparable in Actual: “In ACTUAL rates, the center and max numbers have the same units, and are directly comparable in terms of 'how it feels' in the center compared to further out.”

Expo: the shape never quite matches

Center and max carry over exactly, the shape in between does not. Betaflight rates bend the curve through the fraction with the super rate, Actual through a power of the stick travel. So the converter looks for the Expo, in steps of 0.01, at which the Actual curve comes closest to the old one over the whole stick travel (least squares). For the app's default curve that gives Center Sensitivity 200, Max Rate 670 and Expo 0.56:

StickBetaflight ratesActual, converted
10%21.5 °/s22.1 °/s
25%60.6 °/s63.0 °/s
50%153.8 °/s155.8 °/s
75%315.8 °/s313.2 °/s
90%486.5 °/s487.4 °/s
100%666.7 °/s670.0 °/s

The largest difference here is just before full stick (3.6 °/s at 98% stick). The higher the super rate and RC Rate, the bigger the difference in the last quarter: with RC Rate 1.20 and Rate 0.80 it is 26.8 °/s at 93% stick. That is where you fly flips and rolls; around center you won't notice anything.

How well do your rates fit your stick? The free check measures it on your blackbox log. No account, the file stays with you.

Check my log for free

No log yet? See a real example · Turn on logging, with pictures

For your next flying day
  • Betaflight App, Blackbox tab: logging device onboard flash or SD card, logging rate 1 kHz
  • RC Commands, Setpoint and Gyro on, then “Save and reboot”
  • Fly 3 to 5 packs of normal acro
  • Then get the log off the quad and drop it into the free check

Converter

Rates converter

Pick the Rates Type you fly now and the one you want to switch to, and enter your values from the Betaflight App (PID Tuning → Rate Profile Settings). When you change the type, the fields get the defaults the app sets for that type.

Rates Type
AxisRC RateRateRC Expo
Roll
Pitch
Yaw
Result for Rates Type “Actual”
AxisCenter Sensi­tivityMax RateExpo
Roll2006700.56
Pitch2006700.56
Yaw2006700.56

Largest difference between the curves: all axes 3.6 °/s at 98% stick.

0 %100 %7040BetaflightActual
Curve Roll: dashed Betaflight (your values), solid Actual (converted). Horizontal: stick travel from 0 to 100%, vertical: rotation rate in °/s.

The calculation runs in your browser, nothing is sent.

How to switch

  1. Back up your old values. Type diff in the CLI and save the output, or write down the roll, pitch and yaw rows.
  2. Convert. Enter the values in the converter above.
  3. Change the type. In the app under PID Tuning → Rate Profile Settings, set the Rates Type to “Actual” and confirm with “Change”. The fields then show 70, 670 and 0.
  4. Enter and save. Enter Center Sensitivity, Max Rate and Expo for each axis and click “Save”.

For another target type it works the same way: pick the type under “To” in the converter, set the same Rates Type in the app and fill in the fields from the result. The columns have the same names there.

In the CLI it works like this (the commands apply to the currently selected rate profile, see Setting up Betaflight rates):

# Target quad: your quad (enter its name) set rates_type = ACTUAL set roll_rc_rate = <Center Sensitivity ÷ 10> set roll_srate = <Max Rate ÷ 10> set roll_expo = <Expo × 100> # the same with pitch_… and yaw_… save

Then give it a few packs: the new curve is the same at center and at full stick, but not quite in the last quarter.

Other rates models

The converter above handles all five Rates Types of the app, each into each: Betaflight, Raceflight, KISS, Actual and Quick. The principle is the same as above: keep the center and full stick, and fit the shape in between with the target type’s expo (for Betaflight and KISS, RC Rate and Rate follow from it, for Raceflight Rate and Acro+). This is how the three types not covered yet compute (src/main/fc/rc.c, Betaflight 2026.6.2):

  • Raceflight (applyRaceFlightRates): Expo bends the stick travel with the third power, Rate is the turn rate at full stick without Acro+ in °/s, and Acro+ raises it towards full stick, by Acro+ percent at full stick.
  • KISS (applyKissRates): works like Betaflight rates with the same fraction for Rate, but RC Curve bends with the third instead of the fourth power, there is no increment above RC Rate 2.0, and Rate only goes up to 0.99.
  • Quick (applyQuickRates): RC Rate times 200 is the slope at center, Max Rate the turn rate at full stick, Expo shapes the transition. By default (quickrates_rc_expo = OFF) Expo works in the denominator, not directly on the stick.

How close the new curve gets is shown in the line “Largest difference between the curves”. With the app’s defaults it is 3.7 °/s from Quick to Actual, but 245 °/s from Actual to Quick: Actual’s flat center cannot be rebuilt with Quick at the same center and full-stick rate.

The Betaflight documentation also names a calculator that does all models: “Metamarc's rate converter is probably the best converter and visualiser, supporting all the Rates models currently available in Betaflight.” You can find it at rates.metamarc.com.

Converting is not the same as getting it right

Converting keeps what you are used to, even if it doesn't suit the way you fly. Whether your center is too twitchy or you hardly use full stick only shows in a blackbox log. fpvrates also reads logs flown with Betaflight rates (they are measured as the closest Actual Rates), and the suggested rates come as Actual Rates.

Last updated: Nov 16, 2026